The Art of Basic Plumbing for Installing a Bathtub
Click HereThey are making a number of good pointers about A Step-by-Step Guide to Installing a Bathtub as a whole in the content down the page.
Mounting a bathtub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Replacing an old bathtub with a new one is also a moderately hard job. If the old bathtub is readily obtainable, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to vacate the old tub and also set in the new one. Make certain you have qualified on your own for the work and are comfortable trying it. Instead of employing a contractor to take over a halfway-completed task, it is much better to think about employing one before you start. Chances are you might require an expert plumber to make tube connections.
This post will assist you install a brand-new bathtub in your shower room if you have actually already bought a brand-new bathtub as well as don't need to change the setup of your previous water pipelines.
Your devices and material list must consist of the following:
Getting ready for the Setup
To start with, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to ensure that if the tap comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps device to avoid stress on the bathtub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its final setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is separate the water system. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be quite problematic due to the limited accessibility that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to carrying on to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Making use of both wood boards under its feet, put the tub in the required position. The wooden boards are useful in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; then do the same for the other faucet.
Activate the water supply and check all joints and also brand-new pipework for leaks and also tighten them if necessary. Fill the bathtub and also check the overflow outlet and also the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's instruction manual. Tiling and sealing around the tub should wait until the tub has been made use of a minimum of once as this will resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in area between the faucet as well as the sink. Secure the tap in place with the maker provided backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous type should be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, leading to issues with wetness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and also fittings. They are offered in tubes as well as cartridges, and also can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill up the bathtub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealant can fracture relatively very early if you do not consider this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that editorial on Installing A Bathtub from someone on another web address. Enjoyed reading our piece of writing? Please share it. Help someone else discover it. Kudos for your time. Visit again soon.
Schedule